Skip to content

Fully insured, over 10 years of experience. Free quote

(972) 419-8658
(972) 419-8658
Installer in a cap and tool pouch drilling at the top of a new white storm door frame on the front entry of a brick house, with a ladder and tool bag nearby

ServicesStorm Doors

Storm Doors in Frisco

We install storm doors that fit your entry opening, seal against the brick molding and close softly every time. You get photos of the opening before we start and of the finished frame, closer and sweep, so you can see the work.

Why a second door at the entry pays off

A storm door is a lighter second door, with its own frame, mounted outside your main entry door. It keeps wind-driven rain and dust off the entry, lets a breeze through a screen panel, and takes the daily wear that would otherwise wear down the finish and weatherstripping on your front door.

Fit is where most storm doors fail. Entry openings are rarely perfectly square, so the door hangs from an adjustable expander rail, often called a Z-bar, that takes up the gap at the top or latch side. Set that rail wrong and the door drags, the latch misses and air whistles past the sweep. Before we order a door, we take width and height measurements in three places and compare the diagonals to see how far the opening is out of square.

One detail matters more here than in cooler climates. A full-glass storm door facing hard afternoon sun can trap heat against the entry door behind it, enough to warp some fiberglass doors or blister a dark paint finish. We note which direction your entry faces and what your main door is made of, then suggest glass, a vented design or a screen panel that suits it.

Man in a gray cap holds a fan of white, tan, brown and black frame color samples for a woman at the black front door of a brick house, ladder and caulk gun nearby

What our storm door installation includes

  1. 01

    Measurement and square check

    We take width and height at three points and check the diagonals. Those numbers decide the door size and how much the expander has to take up.

  2. 02

    Door style matched to your entry

    Full-view, mid-view and retractable-screen doors each suit a different use. We explain how each handles light, airflow and heat on your side of the house.

  3. 03

    Frame, expander and sealing

    The hinge rail is fastened to the brick molding, then the drip cap and expander are set so the door hangs plumb. Gaps get sealant where water could run behind the frame.

  4. 04

    Closer, chain and sweep setup

    We set the pneumatic closer's speed so the door shuts without slamming. A wind chain stops a sudden gust from flinging the door past the limit its hinge can take, and the bottom sweep is adjusted to meet the threshold.

  5. 05

    Hardware and lock

    The handle, latch and deadbolt are aligned with the strike so the door locks without lifting or pushing.

  6. 06

    Before-and-after record and cleanup

    You get photos of the opening as we found it and of the finished install. The old door, packaging and cutoffs leave with us.

Questions about Storm Doors?

Call(972) 419-8658

When a storm door is due for replacement

  • The closer has given out

    When the pneumatic closer weakens, the door bangs shut or swings open on its own. On older doors, the rails near the closer bracket are often bent as well.

  • Light showing at the edges

    Gaps of daylight along the top or the latch side mean the expander has shifted or the frame has twisted out of square.

  • A loose or kinked hinge rail

    A single hard gust catching an open door can bend the full-length hinge. From then on the door scrapes and the latch no longer meets the strike.

  • Sun-worn screen and cracked glazing

    Sunlight weakens the screen mesh and the vinyl holding the glass in place. The panels start to rattle and the screen rips along the spline.

  • Trapped heat behind the glass

    An entry door that is hot to touch or has a peeling finish may be sitting behind a storm door that holds in heat. Switching to different glass or a vented style can solve it.

How installation day runs

  1. 1

    Free in-person consultation

    We look at your entry, measure the opening and photograph the brick molding and threshold. You get a written quote with the door, hardware and labor listed separately.

  2. 2

    Remove and inspect

    We take off the old storm door, if there is one, and photograph the molding underneath. If anything there affects the install, we show you the picture before we go further.

  3. 3

    Hang and adjust

    The hinge rail goes on first, then the drip cap and expander. We set the door plumb, mount the closer and chain, and adjust the sweep to the threshold.

  4. 4

    Test and walk through

    We open and close the door several times, test the lock and show you how to adjust closer speed. You get the finished-install pictures, and most installs take part of a single day.

What goes into a storm door price

Storm doors that look the same in a store can differ a lot in price because of how they are built: the frame thickness, the glass and the hardware. The shape of your entry opening matters as well. Your written quote lists each part on its own line. If you would like to pay over time, we offer $0 Down on the whole project and 0% Financing options.

Frame weight and build
Heavier aluminum or a solid core is priced above a lightweight door. That added material helps the door stay true and resist dents.
Glass and screen options
Retractable screens, interchangeable panels and Low-E glass all add to the cost. Each one also affects how much air passes through and how much heat collects behind the door.
Unusual openings
An entry that is wider or taller than usual, or not square, may need a longer expander or a door ordered in a special size.
Locks and color
Custom colors, keyed handles and deadbolt sets are priced above a plain white or bronze door with a simple latch.

Common storm door questions

Can a storm door hurt the entry door behind it?

It can when the glass holds too much heat against a main door that sits in full sun. Some fiberglass doors and dark painted finishes react badly to that. We look at what your door is made of and which way it faces, then suggest a screen panel, a vented design or a suitable glass if there is a risk.

Will a storm door fit my entry?

Most standard entries can take one. The brick molding has to be flat and wide enough to hold the hinge and latch rails, and there must be room so the storm door handle clears the hardware on your main door. We check both at the consultation.

Should I pick full-view or mid-view?

Full-view doors show more of your entry door and let in the most light, and many let you switch between glass and screen panels. Mid-view doors have a solid lower section that holds up better to pets, kids and packages left at the step. How you use the door usually decides it.

Do I need to be home for the install?

We ask that an adult be there when we arrive so we can confirm the style and which side the handle mounts on. We would also like you back at the end to test the lock and closer with us. In between, you can go about your day.

Do you work outside Frisco?

Yes. We install storm doors in nearby towns such as Prosper, Little Elm and The Colony. The full list is on our Service Areas page.

See your storm door options in person

We'll measure your entry, show you how each style handles light and heat, and leave you with a written quote. You'll also see the pictures we take of your opening.